How to Create Stylish Faux Crittall Doors With Reeded Glas

When we were extending and renovating our house, the internal doors where the last thing on my mind. They’re just doors, right? I’ll just choose some from our local DIY store and be done with it. Although I knew at some point, I wanted Crittall style doors in my home. They’re just so stylish!

how to create faux crittall doors pinterest pin

I wanted a glass door in between the utility room and kitchen as it would help distribute light around. We have a large east facing window in the utility so the morning sunshine pours through and helps bring light into this corner of our kitchen.

However, as the glass door and window in the utility are east and north facing, by lunch time a lot of the light has disappeared.

The door to the utility. It’s a nice door
We have a large east facing window in the utility and the sunshine pours in in the morning
We also have a door to the left, just seen

By adding a glass door, it would help keep the utility bright throughout the day from the huge sun lantern we have in the kitchen next to the utility.

This meant we could close the door and still have the light streaming through in the morning. I wrote a blog post on our utility room renovation here


We went with a plain white glass door from B&Q to begin with as it matched the door we already had walking into the kitchen. It was a nice door; I have nothing against it. But I knew eventually that I was going to paint all the doors and skirting boards in the kitchen anthracite grey to match the bifold doors, so that’s when I decided to go with faux crittall on this door.

Eventually, we are looking to occasionally Airbnb the right-hand side of our home out and the utility will double up as a small kitchen.

I was looking at installing blinds on the door so that we had some privacy when we had guests over but I wanted something a little more permanent.

This utility will double up as a small kitchen for guests.

Thankfully, Glass Films got in touch asking if I wanted to do a collaboration and I knew instantly what to do. By adding reeded glass to the faux crittall doors, it would still allow all the light to come into the utility room but give everyone some privacy on either side.

What you will need to create Faux Crittall Doors (film optional!)

How I did it

I was originally going to use electrical tape to create the crittall style frame but as the frame to the door is quite deep, I decided to go with strip wood instead.

I needed to plan where the wooden frames were going to begin with so I used SketchUp to work out the measurements.

I measured the space of the glass and then divided it by 4 to give me the layout of where I needed to put the 3 frames to create a faux crittall style door.

Measure the glass of the door

I cut the strip wood to size using my Mitre saw.

I do love my mitre saw!

Finally, I cleaned the glass using soapy water spray and using the Gorilla glue, I stuck the strip wood to the doors. The glue says you have to put pressure on it for at least an hour so I used a large clamp to hold it in place.

Once the wood was secure, I used Polyfilla to fill in the tiny gaps between the wood and door frame to make it look seamless.

Use a very diluted soapy water solution
And clean!
I used Gorilla glue on the back of the strip wood
And then stuck the strip wood to the glass

The next job was to paint the door and frame. In hindsight, it was probably best to paint the strip wood first! I used Valspar Premium Wood & Metal in Satin Paint and they mixed the colour for me using the Anthracite Grey RAL no. 7016.

Getting the door ready to paint
First coat going on
I love the Anthracite Grey colour

The door needed 3 coats to give it an even coverage and is the perfect colour for that faux crittall look!

Adding the reeded Glass Film

Finally, I needed to add the reeded glass film to the door. Again, I used some soapy water spray to make sure the door was completely clean and then measured out the four sections of the faux crittall door so I could cut the film to size.

It is easy to cut the film

The glass film is self-adhesive so it takes a lot of patience and precision to apply. Spray some soapy water onto the glass and then put the film into place, slowly peeling off the back of the film so that it sticks to the glass.

Using a professional squeegee, slowly squeeze all the bubbles out from under the film and mop up any excess water.

Using the squeegee to squeeze out any excess air

Once you are happy that the film is vertical and in place, use a very sharp cutting knife and the end of your squeegee to cut any excess film away.

Using a sharp cutting knife and end of the squeegee, I cut away the excess film

And that’s all there is to it!

I am so happy with the results of my faux crittall style door and the reeded film helps give us some privacy if we ever get around to renting out this side of our house.

I just need to paint all our over internal doors anthracite grey!

This corner of our kitchen is coming along nicely.
I love the colour and the reeded glass film gives us some privacy without compromising on the light

It’s so easy to do and I love the results. Let me know if you have any questions.

Mel x

how to create faux crittall doors with reeded glass pinterest pin

Leave a Reply

Your email address will not be published. Required fields are marked *